Honeywell T8602D Instrukcja Użytkownika Pobierz pdf

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1510-

T8602D Chronotherm® IV

Programmable Thermostats

APPLICATION

The T8602 Chronotherm® IV Programmable Thermostat

provides electronic control of 24 Vac single-stage heating

and cooling systems or 750 mV heating and 750 mV

cooling. Refer to Table 1 for a general description of the

thermostat. All T8602 Thermostats are powered by

batteries.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause

a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 1.5m (5 ft) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Wallplate Installation

The thermostat can be mounted horizontally on the wall

or on a 50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.

Position wallplate horizontally on the wall or on a

50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat will function properly even

when not level.

2. Use a pencil to mark the mounting holes. See Fig.

3. Remove the wallplate from the wall and drill two

4.76 mm (3/16 in.) holes in the wall (if drywall) as

marked. For firmer material such as plaster, drill

two 5.56 mm (7/32 in.) holes. Gently tap anchors

(provided) into the drilled holes until flush with the

wall.

4. Position the wallplate over the holes, pulling wires

through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

Table 1. Description of T8602 Thermostats.

T8602 System Changeover

System

Selection

Fan

Selection Comments

D Heat-Cool Manual or

Automatic

Selectable

Heat-Off-Cool or

Heat-Off-Cool-Auto

On-Auto System and fan selections are done

by keyboard.

1 2 3 4 5 6 ... 11 12

Podsumowanie treści

Strona 1 - Programmable Thermostats

Strona 2 - 69-1510-4 2

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS69-1510-4 10THERMOSTAT INFORMATION1. Press the Time ∆ key to access the thermostat information.2. Press

Strona 3 - Mounting Thermostat

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS11 69-1510-4TROUBLESHOOTING GUIDETable 6. Troubleshooting Guide.Symptom Possible Cause ActionDisplay wi

Strona 4 - SETTINGS

69-1510-4 G.H. Rev. 03-03 www.honeywell.com/yourhomePrinted in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.Autom

Strona 5 - INSTALLER SETUP

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS69-1510-4 2Fig. 1. Typical location of thermostat.Fig. 2. Mounting the wallplate.WIRINGAll wiring must

Strona 6 - 69-1510-4 6

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS3 69-1510-4Fig. 4. Typical hookup in heat and cool system with one transformer.Fig. 5. Typical hookup i

Strona 7 - 7 69-1510-4

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS69-1510-4 4Using Thermostat KeysThe thermostat keys are used to:• set current day and time,• program ti

Strona 8 - INSTALLER SYSTEM TEST

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS5 69-1510-4Temperature SettingsRefer to Table 2 for the default program settings. If the daytime energy

Strona 9 - 9 69-1510-4

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS69-1510-4 6Table 3. Thermostat Installer Setup Options.SelectInstaller Setup Number (Press Time ∆ key t

Strona 10 - CHECKOUT

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS7 69-1510-4IMPORTA N TReview the settings to confirm that they match the system. Press Run Program to e

Strona 11 - TROUBLESHOOTING GUIDE

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS69-1510-4 8Setting Current Day and Time1. Press Set Current Day/Time.NOTE: On initial powerup or after

Strona 12 - Printed in U.S.A. on recycled

T8602D CHRONOTHERM® IV PROGRAMMABLE THERMOSTATS9 69-1510-4NOTE: Press any key and the displayed numbers will change. Press Time ∇ to go to the previou

Komentarze do niniejszej Instrukcji

Brak uwag

Honeywell T8602D Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Termostaty Honeywell T8602D. Honeywell T8602D User's Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Termostaty Honeywell T8602D